Home / Products / Comet Cable Glands / Comet Single Compression Type Heavy Duty Cable Gland
Comet Single Compression Type Heavy Duty Cable Gland
Indoor Gland For Single Wire Armoured Cables |
||||||
Gland reference |
Cable dimensions |
Gland dimensions |
||||
| Diameter | Entry thread | Across flats (E) |
Across corners (F) |
|||
| Under armour (A) |
Overall Diameter (B) |
Entry (C) |
Length (D) |
|||
| size | mm | mm | inch | mm | mm | mm |
| 1616 | 9.0 | 15.0 | 5/8" | 8.5 | 25.0 | 29.0 |
| 1619 | 10.0 | 15.0 | 3/4" | 8.5 | 25.0 | 29.0 |
| 2119 | 14.0 | 20.0 | 3/4" | 9.5 | 30.5 | 35.0 |
| 2125 | 14.0 | 20.0 | 1" | 9.5 | 30.5 | 35.0 |
| 2925 | 20.0 | 26.0 | 1" | 10.0 | 40.0 | 46.0 |
| 2932 | 24.0 | 29.0 | 1.1/4" | 10.0 | 40.0 | 46.0 |
| 2938 | 24.0 | 29.0 | 1.1/2" | 10.0 | 40.0 | 46.0 |
| 3638 | 31.0 | 37.0 | 1.1/2" | 11.0 | 49.0 | 56.0 |
| 4251 | 36.0 | 42.0 | 2" | 11.0 | 60.0 | 68.0 |
| 5451 | 44.0 | 50.0 | 2" | 12.0 | 67.0 | 77.0 |
| 5463 | 44.0 | 50.0 | 2.1/2" | 12.0 | 67.0 | 77.0 |
| 6063 | 54.0 | 60.0 | 2.1/2" | 12.0 | 78.0 | 88.0 |
| 6675 | 60.0 | 66.0 | 3" | 13.0 | 84.0 | 96.0 |
| 7882 | 70.0 | 77.0 | 3.1/4" | 14.0 | 98.0 | 112.0 |
Application :
For use under most climatic conditions.This are Weatherproof and may be used in the corrosive conditions when protected by the shroud.
Specification :
Gland consist of checknut 1, gland body 2, metal washers (3 Nos) 3, outer seal rubber ring 4, compression nut 5. All metal parts are made of brass accurately machined for ease of assembly.
Accesories :
Shrouds and Earth tags are supplied separately and should be specified when ordering the gland.
Materials & Finishes :
M.O.C :
a. Cable Gland is manufactured in Brass (standard).
b. Alternate material - Stainless Steel / Aluminium.
Sealing Ring : Natural Rubber
Thread :
a. Glands are supplied with B.S.C. thread (ET) as standard.
b. Alternate thread forms available are - NPT / PG / BSP / MM etc.
Finish : a. Nickel Plated (standard)
b. Alternate Plating - Tin / Cadmium / Chrome
Protection Class : IP 60
Ref Standard : IS 12943
Fiting Sequence
a) Screw item 2 into apparatus (secure with item 1 if plain hole entry.)
b) Pass item 5, item 3 and item 4 over cable before commencing to strip oversheath.
c) Remove the outer sheath to the desired length depending on the length of leads required.
d) Pass item 3 over the cable and splay out the armour wire one by one and then cut the armour wires according to the size of washer. Insert the third metal washer over inner sheath of cable so that bend armour are secured between the two metal washers.
e) Push the cable through item 2 and engage the item 5 with item 2 and tighten up while doing, so the grooved rubber ring will contract in radial direction and will grip the outer sheath of cable.
